Search results
Jump to navigation
Jump to search
- <b>NOTE:</b> Direct announcements of AMPRNet address allocations are usually reserv <b>NOTE:</b> How your ISP chooses to forward traffic for your AMPRNet allocation va ...2 KB (270 words) - 14:01, 3 May 2022
- Note to editor: when this is complete and tested, link to home page. ...518 bytes (88 words) - 11:33, 25 July 2019
- Note that an IP address ''must'' be associated with a domain name in AMPR.ORG in ...871 bytes (141 words) - 10:08, 2 February 2024
- ## From the regional network page, request an allocation. Note, select only ONE of the connection options (Radio, Tunnel, or Direct). To s ...email hostmaster@ardc.net and someone will get back to you and assist you. Note that the main tunnel router at UCSD will NOT pass traffic to an IP address ...3 KB (441 words) - 16:20, 20 January 2024
- Note that ARDC is <b>not</b> an internet service provider. It does not provide a ...1,007 bytes (145 words) - 22:11, 27 July 2023
- '''NOTE: DO ''NOT'' RUN APT-GET UPGRADE!!!! This will break many things within VyOS Note: Close out of the file and save it, by doing Ctrl-X, then pressing 'Y', the ...4 KB (624 words) - 17:52, 29 March 2022
- * Please note, this is an introduction to the new portal released on April 3rd, 2024. ...2 KB (373 words) - 07:10, 3 April 2024
- To enable input of IPENCAP (IP Protocol Number 4) '''Note: this rule is required for other AMPR nodes to initiate inbound traffic to '''NOTE:''' ...14 KB (1,689 words) - 16:17, 25 April 2019
- '''NOTE:''' '''NOTE - ''' ''these instructions assume:'' ...9 KB (1,352 words) - 06:51, 7 November 2020
- '''(NOTE: A script has been developed to streamline setup of a [[Gateway]], see: [[s '''Note:''' If you are using a home router or wireless access point, you will need ...22 KB (3,468 words) - 20:19, 26 May 2017
- Note: Functionally, a VPN and a tunnel do much the same thing, except a VPN is d Installing BGP is beyond the scope of this FAQ. Note however that you must have written permission from the administrator of the ...14 KB (2,371 words) - 07:56, 25 March 2024
- <span style="color: red;">'''NOTE: THE SETUP SCRIPT DOES NOT SECURE YOUR ROUTER. YOU NEED TO SET UP FIREWALL <span style="color: red;">'''NOTE: THE SETUP SCRIPT DOES NOT SECURE YOUR ROUTER. YOU NEED TO SET UP FIREWALL ...9 KB (1,556 words) - 01:15, 18 December 2023
- ...the router with the command <code>traceroute 44.88.0.1 -s 44.1.2.0</code>. Note that this does not stop you from assigning your allocation to an Ethernet i ...4 KB (687 words) - 10:51, 8 April 2019
- ...ages (host or port unreachable, for example), have a valid source address. Note that despite the fact that this is a point-to-point interface, we do not sp Note the <code>0.0.0.0</code> as the remote address in the <code>ifconfig tunnel ...21 KB (3,152 words) - 02:19, 28 April 2024
- '''NOTE: if you do not wish to compile software, you must use [[rip44d]] or [[Encap ...(used in a script to reload table 44 on boot) and '''/etc/cron.hourly/'''. Note that: '''startampr''' has properly named those files. If you wish to edit t ...18 KB (2,833 words) - 11:46, 25 July 2019
- *** Please note that this was tested to work on 2651XM or better, expect poor resp- *** ...19 KB (2,768 words) - 17:53, 29 March 2022