44Net Connect/Quick Start/Debian based distributions - Revision history

KN6DWI: Move display title and table of contents configuration inside noinclude block

2026-06-03T22:13:08Z

Move display title and table of contents configuration inside noinclude block

← Older revision		Revision as of 22:13, 3 June 2026
Line 1:		Line 1:
			<noinclude>
	<div class="toclimit-3">		<div class="toclimit-3">
	__TOC__		__TOC__
Line 4:		Line 5:
	{{DISPLAYTITLE:44Net Connect Quick Start: Debian-based distributions}}		{{DISPLAYTITLE:44Net Connect Quick Start: Debian-based distributions}}

	~~<noinclude>~~
	=== What you need ===		=== What you need ===

KN6DWI: Fix display title

2026-06-03T22:11:27Z

Fix display title

← Older revision		Revision as of 22:11, 3 June 2026
Line 2:		Line 2:
	__TOC__		__TOC__
	</div>		</div>
	{{DISPLAYTITLE:44Net Connect Quick Start: ~~Raspberry Pi~~}}		{{DISPLAYTITLE:44Net Connect Quick Start: Debian-based distributions}}

	<noinclude>		<noinclude>

KN6DWI: Paste in the rest of the content from the Raspberry Pi page

2026-06-03T22:10:43Z

Paste in the rest of the content from the Raspberry Pi page

@@ Line 4: / Line 4: @@
 {{DISPLAYTITLE:44Net Connect Quick Start: Raspberry Pi}}
 === What you need ===
@@ Line 13: / Line 14: @@
 If you haven't set up your Portal account or verified your callsign yet, see [[GetStarted|44Net: Get Started]] for instructions. If you haven't obtained a WireGuard tunnel configuration file from 44Net Connect, get one using the [[44Net_Connect/Quick_Start|the 44Net Connect quick start guide]]
+</noinclude>
 == Install Dependencies ==
@@ Line 28: / Line 29: @@
 The third line, beginning with "Active," should indicate that the unit is active (running).
 If it's not, run <code>systemctl start systemd-resolved</code> to start the unit. This will ensure that the unit is currently running.

KN6DWI: Created page and pasted some content from 44Net Connect/Quick Start/Raspberry Pi

2026-06-03T21:39:21Z

Created page and pasted some content from 44Net Connect/Quick Start/Raspberry Pi

New page

<div class="toclimit-3">
__TOC__
</div>
{{DISPLAYTITLE:44Net Connect Quick Start: Raspberry Pi}}

=== What you need ===

* A 44Net Portal account
* A verified amateur radio callsign
* A configuration file from 44Net Connect
* A machine running a Debian-based Linux distribution
* Some sort of Internet access

If you haven't set up your Portal account or verified your callsign yet, see [[GetStarted|44Net: Get Started]] for instructions. If you haven't obtained a WireGuard tunnel configuration file from 44Net Connect, get one using the [[44Net_Connect/Quick_Start|the 44Net Connect quick start guide]]

== Install Dependencies ==

=== Step 1: Ensure your OS is up to date ===
Open a terminal and run <code>sudo apt-get update</code>, then <code>sudo apt-get upgrade</code>.

=== Step 2: Install wireguard and systemd-resolved ===
Run <code>sudo apt-get install wireguard systemd-resolved</code>, then restart your Raspberry Pi. Restarting is required for <code>systemd-resolved</code> to function.

=== Step 3: Verify that systemd-resolved is enabled ===
Run <code>systemctl status systemd-resolved</code>. If the unit is running without issues, there will be a green asterisk or circle at the top left. The second line, beginning with "Loaded," should indicate that the unit is enabled. If it's not, run <code>systemctl enable systemd-resolved</code> to enable the unit. This will ensure that the unit starts automatically when your Raspberry Pi boots from now on.

The third line, beginning with "Active," should indicate that the unit is active (running).
If it's not, run <code>systemctl start systemd-resolved</code> to start the unit. This will ensure that the unit is currently running.