Ampr-map - Revision history

KI5QKX: mw push

2026-03-01T00:14:57Z

mw push

2026-02-28T23:20:43Z

mw push

← Older revision		Revision as of 23:20, 28 February 2026
Line 62:		Line 62:
	;; 4. 'Radio' positions		;; 4. 'Radio' positions

	These positions are dedicated to stations not directly reachable via ~~44net~~, and are sent out by other systems in their name.		These positions are dedicated to stations not directly reachable via 44Net, and are sent out by other systems in their name.

	To do this, do a periodic fetch on the following URL:		To do this, do a periodic fetch on the following URL:
Line 81:		Line 81:
	Positions will be shown as grey dots.		Positions will be shown as grey dots.

	== Map ~~Server Source Code~~ ==		== Map server source code ==

	The map server's source code can be found in the AMPR GIT repository:		The map server's source code can be found in the AMPR GIT repository:

2025-09-06T21:08:25Z

← Older revision		Revision as of 21:08, 6 September 2025
Line 81:		Line 81:
	Positions will be shown as grey dots.		Positions will be shown as grey dots.

			== Map Server Source Code ==

			The map server's source code can be found in the AMPR GIT repository:

			<nowiki>https://git.ampr.org/yo2loj/ampr-map-server</nowiki>

	[[Category:Reference]]		[[Category:Reference]]

2024-12-12T20:23:43Z

← Older revision		Revision as of 20:23, 12 December 2024
Line 80:		Line 80:

	Positions will be shown as grey dots.		Positions will be shown as grey dots.


			[[Category:Reference]]

2024-08-28T21:31:17Z

← Older revision		Revision as of 21:31, 28 August 2024
Line 22:		Line 22:

	http://www.yo2loj.ro/ampr-map/		http://www.yo2loj.ro/ampr-map/
	http://~~yo2tm~~.ampr.org/ampr-map/		http://yo2loj.ampr.org/ampr-map/

	== Sending the location to the map ==		== Sending the location to the map ==

2022-10-25T06:08:17Z

Sending the location to the map

← Older revision		Revision as of 06:08, 25 October 2022
Line 46:		Line 46:
	Add your locator in the configuration file, under your interface section:		Add your locator in the configuration file, under your interface section:

	call_home = ~~YO2LOJ~~-T@KN05or		call_home = N0CALL-T@KN05or

	Positions will be shown as blue dots.		Positions will be shown as blue dots.

2019-04-19T20:10:10Z

← Older revision		Revision as of 20:10, 19 April 2019
Line 55:		Line 55:
	Set up a cyclic job to run a script in which you request a specific URL, using the command, e.g. every 5 minutes:		Set up a cyclic job to run a script in which you request a specific URL, using the command, e.g. every 5 minutes:

	/tool fetch mode=http url="http://44.182.21.1:59001/mikrotik?id=N0CALL-T@kn01aa" keep-result=no		/tool fetch mode=http url="<nowiki>http://44.182.21.1:59001/mikrotik?id=N0CALL-T@kn01aa</nowiki>" keep-result=no

	Positions will be shown as pink dots.		Positions will be shown as pink dots.
Line 66:		Line 66:
	To do this, do a periodic fetch on the following URL:		To do this, do a periodic fetch on the following URL:

	http://44.182.21.1:59001/radio_gateway?id=n0call-t@kn01aa		<nowiki>http://44.182.21.1:59001/radio_gateway?id=n0call-t@kn01aa</nowiki>

	For radio stations, the position time-out is 3 hours.		For radio stations, the position time-out is 3 hours.
Line 77:		Line 77:
	For other (generic) systems, do a periodic fetch on the following URL:		For other (generic) systems, do a periodic fetch on the following URL:

	http://44.182.21.1:59001/generic?id=n0call-t@kn01aa		<nowiki>http://44.182.21.1:59001/generic?id=n0call-t@kn01aa</nowiki>

	Positions will be shown as grey dots.		Positions will be shown as grey dots.

2019-04-19T19:47:04Z

← Older revision		Revision as of 19:47, 19 April 2019
Line 12:		Line 12:
	Some technical info:		Some technical info:
	<blockquote>		<blockquote>
	<i>The ~~system~~ uses following incoming ports:<br>		<i>The server uses the following incoming ports:<br>
	- ampr-ripd uses UDP/59001,<br>		- ampr-ripd uses UDP/59001,<br>
	- amprd uses UDP/59002,<br>		- amprd uses UDP/59002,<br>
Line 18:		Line 18:
	Map events sent to your browser are in json format and use websockets or event-stream as a fallback.</i>		Map events sent to your browser are in json format and use websockets or event-stream as a fallback.</i>
	</blockquote>		</blockquote>


	The map can be reached via these URLs:		The map can be reached via these URLs:

2019-04-19T19:45:42Z

← Older revision		Revision as of 19:45, 19 April 2019
Line 16:		Line 16:
	- amprd uses UDP/59002,<br>		- amprd uses UDP/59002,<br>
	- all other http requests use TCP/59001<br>		- all other http requests use TCP/59001<br>
	Map events sent to your browser use websockets ~~and~~ event-stream as a fallback.</i>		Map events sent to your browser are in json format and use websockets or event-stream as a fallback.</i>
	</blockquote>		</blockquote>

2019-04-19T19:43:48Z

Added technical info

← Older revision		Revision as of 19:43, 19 April 2019
Line 9:		Line 9:

	To opt out, just stop sending position reports...		To opt out, just stop sending position reports...

			Some technical info:
			<blockquote>
			<i>The system uses following incoming ports:<br>
			- ampr-ripd uses UDP/59001,<br>
			- amprd uses UDP/59002,<br>
			- all other http requests use TCP/59001<br>
			Map events sent to your browser use websockets and event-stream as a fallback.</i>
			</blockquote>