IPIP Mesh/Ubiquiti EdgeRouter - Revision history

KI5QKX: Organize IPIP Mesh documentation and navigation

2026-09-29T19:08:55Z

Organize IPIP Mesh documentation and navigation

← Older revision		Revision as of 19:08, 29 September 2026
Line 1:		Line 1:
			{{Section nav\|hub=IPIP Mesh\|title=IPIP Mesh\|category=IPIP Mesh}}

	'''== Updated 26/09/2025 - KC6GNJ =='''		'''== Updated 26/09/2025 - KC6GNJ =='''

2026-09-29T19:08:54Z

← Older revision	Revision as of 19:08, 29 September 2026
(No difference)

2026-09-28T22:28:15Z

mw push

← Older revision		Revision as of 22:28, 28 September 2026
Line 243:		Line 243:
	[[Category:Infrastructure]]		[[Category:Infrastructure]]
	[[Category:Gateways]]		[[Category:Gateways]]
			[[Category:Device and platform guides]]

2026-04-30T18:52:53Z

mw push

← Older revision		Revision as of 18:52, 30 April 2026
Line 2:		Line 2:

	'''== Updated 16/05/2020 - M0MUX =='''		'''== Updated 16/05/2020 - M0MUX =='''


	== The Definitive Document on "Setting up a gateway on Ubiquiti EdgeRouter" (Draft) ==		== The Definitive Document on "Setting up a gateway on Ubiquiti EdgeRouter" (Draft) ==
Line 152:		Line 151:
	• Select tun0 as the interface and select in as the direction.		• Select tun0 as the interface and select in as the direction.
	• Finish by pressing the Save Ruleset button.		• Finish by pressing the Save Ruleset button.


	== Example config ==		== Example config ==
Line 241:		Line 239:
	}		}

			[[Category:How-To]]

	[[Category:How-To Guides]]		[[Category:How-To Guides]]
	[[Category:Infrastructure]]		[[Category:Infrastructure]]
	[[Category:Gateways]]		[[Category:Gateways]]

2026-03-01T00:14:53Z

mw push

2026-02-28T23:20:38Z

mw push

← Older revision		Revision as of 23:20, 28 February 2026
Line 17:		Line 17:
	This guide is specific to only one tunnel to the master AMPRnet gateway at UCSD. This guide doesn't cover the setup of tunnels to other gateways.		This guide is specific to only one tunnel to the master AMPRnet gateway at UCSD. This guide doesn't cover the setup of tunnels to other gateways.

	== Assumptions / ~~Prereqs~~ ==		== Assumptions / prereqs ==

	• You have already registered with AMPRNet and got your 44Net allocation at https://portal.ampr.org.		• You have already registered with AMPRNet and got your 44Net allocation at https://portal.ampr.org.
Line 45:		Line 45:
	'''You need to establish a Gateway for your 44 network, that the clients will route through.'''		'''You need to establish a Gateway for your 44 network, that the clients will route through.'''

	We are going to use the ~~44net~~ allocation of 44.131.252.64/28		We are going to use the 44Net allocation of 44.131.252.64/28

	The gateway will be the next usable IP in the block: 44.131.252.65		The gateway will be the next usable IP in the block: 44.131.252.65
Line 154:		Line 154:


	== Example ~~Config~~ ==		== Example config ==

	This is from my working ER4.		This is from my working ER4.

2026-02-27T19:06:47Z

mw push

2025-09-28T15:17:37Z

Setting up the tunnel

← Older revision		Revision as of 15:17, 28 September 2025
Line 62:		Line 62:

	[ From here down needs serious re-work - Tim KC6GNJ]		[ From here down needs serious re-work - Tim KC6GNJ]

			Just in case you already have tunnels

	In configuration mode enter the following commands		In configuration mode enter the following commands
	<pre>		<pre>
	~~set interfaces tunnel tun44~~
	set interfaces tunnel tun44 local-ip <put the external ip assigned to you by your ISP>		set interfaces tunnel tun44 local-ip <put the external ip assigned to you by your ISP>
	set interfaces tunnel tun44 remote-ip 169.228.34.84		set interfaces tunnel tun44 remote-ip 169.228.34.84

2025-09-26T03:23:40Z

Setting up the tunnel

← Older revision		Revision as of 03:23, 26 September 2025
Line 60:		Line 60:

	== Setting up the tunnel ==		== Setting up the tunnel ==

			[ From here down needs serious re-work - Tim KC6GNJ]

	In configuration mode enter the following commands		In configuration mode enter the following commands
Line 73:		Line 75:
	To verify your input so far, enter the following command		To verify your input so far, enter the following command
	<pre>		<pre>
	show interfaces tunnel ~~tun0~~		show interfaces tunnel tun44
	</pre>		</pre>
	The output should look like this		The output should look like this

2025-09-26T03:13:41Z

Setting up the tunnel

← Older revision		Revision as of 03:13, 26 September 2025
Line 63:		Line 63:
	In configuration mode enter the following commands		In configuration mode enter the following commands
	<pre>		<pre>
	set interfaces tunnel ~~tun0~~		set interfaces tunnel tun44
	set interfaces tunnel ~~tun0~~ local-ip <put the external ip assigned to you by your ISP>		set interfaces tunnel tun44 local-ip <put the external ip assigned to you by your ISP>
	set interfaces tunnel ~~tun0~~ remote-ip 169.228.34.84		set interfaces tunnel tun44 remote-ip 169.228.34.84
	set interfaces tunnel ~~tun0~~ encapsulation ipip		set interfaces tunnel tun44 encapsulation ipip
	set interfaces tunnel ~~tun0~~ description "Tunnel to AMPRNet gateway"		set interfaces tunnel tun44 description "Tunnel to AMPRNet gateway"
	~~</pre>~~		# Now commit the changes
	Now commit the changes
	~~<pre>~~
	commit ; save		commit ; save
	</pre>		</pre>
Line 84:		Line 82:
	remote-ip 169.228.34.84		remote-ip 169.228.34.84
	</pre>		</pre>

	== Setting up source address routing policy ==		== Setting up source address routing policy ==