K2IE - Revision history

KI5QKX: mw push

2026-03-01T00:14:27Z

mw push

← Older revision		Revision as of 00:14, 1 March 2026
Line 194:		Line 194:

	[[Category:How-To Guides]]		[[Category:How-To Guides]]
			[[Category:Infrastructure]]
			[[Category:Gateways]]
			[[Category:Routing]]
			[[Category:Projects]]

KI5QKX: mw push

2026-02-28T23:20:13Z

mw push

← Older revision		Revision as of 23:20, 28 February 2026
Line 98:		Line 98:
	# Dynamic filter, -s argument creates encap.txt		# Dynamic filter, -s argument creates encap.txt
	'''# ./etc/config/ampr-ripd -p <PASSWORD> -s -t 44 -a <44.xxx.xxx.xxx/xx> -x ./etc/config/load_ipipfilter.sh &'''		'''# ./etc/config/ampr-ripd -p <PASSWORD> -s -t 44 -a <44.xxx.xxx.xxx/xx> -x ./etc/config/load_ipipfilter.sh &'''
	## Allows traceroute to respond using ~~44net~~ IP of tunl0 or br-amprlan ##		## Allows traceroute to respond using 44Net IP of tunl0 or br-amprlan ##
	echo 1 > /proc/sys/net/ipv4/icmp_errors_use_inbound_ifaddr		echo 1 > /proc/sys/net/ipv4/icmp_errors_use_inbound_ifaddr

Line 144:		Line 144:
	option lookup '44'		option lookup '44'

	### You must add an IP rule for all ~~44net~~ IPs residing on the device		### You must add an IP rule for all 44Net IPs residing on the device
	config rule		config rule
	option src '44.xxx.xxx.0/24		option src '44.xxx.xxx.0/24
Line 185:		Line 185:
	* '''reboot'''		* '''reboot'''

	== See ~~Also~~ ==		== See also ==

	* [[ampr-ripd]]		* [[ampr-ripd]]

K2IE at 17:32, 15 September 2025

2025-09-15T17:32:01Z

← Older revision		Revision as of 17:32, 15 September 2025
Line 38:		Line 38:
	== Express setup ==		== Express setup ==

	~~(work in progress~~, ~~depends upon~~ package ~~publication)~~		Beginning with OpenWrt 24.10, ampr-ripd is offered as an included package. This greatly simplifies installation on a working OpenWrt system.

	This procedure provides an express method to a working ampr-ripd instance along with the necessary configuration to participate in the ARDC IPIP Mesh. You will need to know the 44.x host address that you will assign to your router, the network number assigned to you, and the full netmask.		This procedure provides an express method to a working ampr-ripd instance along with the necessary configuration to participate in the ARDC IPIP Mesh. You will need to know the 44.x host address that you will assign to your router, the network number assigned to you, and the full netmask.

K2IE at 14:09, 27 May 2025

2025-05-27T14:09:14Z

← Older revision		Revision as of 14:09, 27 May 2025
Line 3:		Line 3:
	TL;DR		TL;DR

	Skip to [[Express setup]]		Skip to [[#Express setup \| Express setup]]

	== Running the [[RIP\| RIP44 protocol]] ==		== Running the [[RIP\| RIP44 protocol]] ==

K2IE at 14:07, 27 May 2025

2025-05-27T14:07:00Z

← Older revision		Revision as of 14:07, 27 May 2025
Line 3:		Line 3:
	TL;DR		TL;DR

	~~Skit~~ to [[Express ~~Setup~~]]		Skip to [[Express setup]]

	== Running the [[RIP\| RIP44 protocol]] ==		== Running the [[RIP\| RIP44 protocol]] ==

K2IE at 14:04, 27 May 2025

2025-05-27T14:04:17Z

← Older revision		Revision as of 14:04, 27 May 2025
Line 1:		Line 1:
	This Wiki provides operators a straightforward method of configuring your OpenWrt device for use with the [[ARDC]] network.		This Wiki provides operators a straightforward method of configuring your OpenWrt device for use with the [[ARDC]] network.

			TL;DR

			Skit to [[Express Setup]]

	== Running the [[RIP\| RIP44 protocol]] ==		== Running the [[RIP\| RIP44 protocol]] ==

K2IE at 14:00, 27 May 2025

2025-05-27T14:00:27Z

K2IE: /* Setup and configuration of OpenWrt */

2025-05-15T09:49:31Z

Setup and configuration of OpenWrt

← Older revision		Revision as of 09:49, 15 May 2025
Line 65:		Line 65:
	STOP HERE. What follows is an explanation of how to manually install and configure ampr-ripd. This was a method that was followed prior to the publication of the OpenWrt ampr-ripd package.		STOP HERE. What follows is an explanation of how to manually install and configure ampr-ripd. This was a method that was followed prior to the publication of the OpenWrt ampr-ripd package.

	== ~~Setup~~ and configuration of OpenWrt ==		== Manual setup and configuration of OpenWrt ==

	'''Install:'''		'''Install:'''

	* [https://openwrt.org/packages/pkgdata/kmod-ipip kmod-ipip]		* [https://openwrt.org/packages/pkgdata/kmod-ipip kmod-ipip]
	* [https://openwrt.org/packages/pkgdata/ip-full ip-~~full~~]		* [https://openwrt.org/packages/pkgdata/ip-full ip-tiny]
	* [https://openwrt.org/packages/pkgdata/libstdcpp libstdcpp] (depending on version, it may now be named [https://openwrt.org/packages/pkgdata/libstdcpp6 libstdcpp6])		* [https://openwrt.org/packages/pkgdata/libstdcpp libstdcpp] (depending on version, it may now be named [https://openwrt.org/packages/pkgdata/libstdcpp6 libstdcpp6])

K2IE: /* Running the RIP44 protocol */

2025-05-15T09:47:03Z

Running the RIP44 protocol

← Older revision		Revision as of 09:47, 15 May 2025
Line 10:		Line 10:
	''Therefore:''		''Therefore:''

	* '''You must have access to a binary [https://en.wikipedia.org/wiki/Executable executable] of [[ampr-ripd]] that is compatible with the [https://en.wikipedia.org/wiki/Central_processing_unit CPU] in your OpenWrt device (e.g. i386, i586, x86_64, MIPS, PPC, etc.). An OpenWrt package is available to install and configure ampr-ripd (see [[Express setup]]. Alternatively, install the packages necessary to run [[rip44d]].'''		* '''You must have access to a binary [https://en.wikipedia.org/wiki/Executable executable] of [[ampr-ripd]] that is compatible with the [https://en.wikipedia.org/wiki/Central_processing_unit CPU] in your OpenWrt device (e.g. i386, i586, x86_64, MIPS, PPC, etc.). An OpenWrt package is available to install and configure ampr-ripd (see Express setup below). Alternatively, install the packages necessary to run [[rip44d]].'''
	* '''[[ampr-ripd]]''' (written in C by YO2LOJ) is used in this Wiki example, as fewer prerequisite software are required (e.g. C++ library), compared to [[rip44d]]		* '''[[ampr-ripd]]''' (written in C by YO2LOJ) is used in this Wiki example, as fewer prerequisite software are required (e.g. C++ library), compared to [[rip44d]]
	* ''There is also an experimental [[RIP44.lua]] daemon which should run with standard packages''		* ''There is also an experimental [[RIP44.lua]] daemon which should run with standard packages''

K2IE: /* Running the RIP44 protocol */

2025-05-15T09:45:35Z

Running the RIP44 protocol

← Older revision		Revision as of 09:45, 15 May 2025
Line 10:		Line 10:
	''Therefore:''		''Therefore:''

	* '''You must have access to a binary [https://en.wikipedia.org/wiki/Executable executable] of [[ampr-ripd]] that is compatible with the [https://en.wikipedia.org/wiki/Central_processing_unit CPU] in your OpenWrt device (e.g. i386, i586, x86_64, MIPS, PPC, etc.). An OpenWrt package is available to install and configure ampr-ripd (see [[Express ~~Install~~]]. Alternatively, install the packages necessary to run [[rip44d]].'''		* '''You must have access to a binary [https://en.wikipedia.org/wiki/Executable executable] of [[ampr-ripd]] that is compatible with the [https://en.wikipedia.org/wiki/Central_processing_unit CPU] in your OpenWrt device (e.g. i386, i586, x86_64, MIPS, PPC, etc.). An OpenWrt package is available to install and configure ampr-ripd (see [[Express setup]]. Alternatively, install the packages necessary to run [[rip44d]].'''
	* '''[[ampr-ripd]]''' (written in C by YO2LOJ) is used in this Wiki example, as fewer prerequisite software are required (e.g. C++ library), compared to [[rip44d]]		* '''[[ampr-ripd]]''' (written in C by YO2LOJ) is used in this Wiki example, as fewer prerequisite software are required (e.g. C++ library), compared to [[rip44d]]
	* ''There is also an experimental [[RIP44.lua]] daemon which should run with standard packages''		* ''There is also an experimental [[RIP44.lua]] daemon which should run with standard packages''

← Older revision		Revision as of 14:00, 27 May 2025
Line 37:		Line 37:
	(work in progress, depends upon package publication)		(work in progress, depends upon package publication)

	This procedure provides an express method to a working ampr-ripd ~~instanc~~ along with the necessary configuration to participate in the ARDC IPIP Mesh. You will need to know the 44.x host address that you will assign to your router, the network number assigned to you, and the full netmask.		This procedure provides an express method to a working ampr-ripd instance along with the necessary configuration to participate in the ARDC IPIP Mesh. You will need to know the 44.x host address that you will assign to your router, the network number assigned to you, and the full netmask.

	'''Install:'''		'''Install:'''
Line 49:		Line 49:
	In this example, 44.127.255.1 is the address assigned to your OpenWrt host. 255.255.255.0 is the associated netmask. 44.127.255.0 is your assigned network number.		In this example, 44.127.255.1 is the address assigned to your OpenWrt host. 255.255.255.0 is the associated netmask. 44.127.255.0 is your assigned network number.

	* /etc/init.d/ampr-ripd configre 44.127.~~255~~.1 255.255.~~255~~.0 44.127.~~255~~.0		* /etc/init.d/ampr-ripd configre 44.127.254.1 255.255.254.0 44.127.254.0
	* /etc/iit.d/ampr-ripd restart		* /etc/iit.d/ampr-ripd restart
	* /etc/init.d/network restart		* /etc/init.d/network restart
Line 61:		Line 61:
	You should see routes to other IPIP Mesh sites.		You should see routes to other IPIP Mesh sites.

	You'll have to create firewall rules allowing the desired connectivity.		You'll have to create firewall rules allowing the desired connectivity. By default, the package allows ping from AMPRWAN to your gateway and to AMPRLAN hosts behind the gateway. It also creates a rule to allow IPIP tunneling (protocol 4). Anything else is up to you and based upon your requirements.

	STOP HERE. What follows is an explanation of how to manually install and configure ampr-ripd. This was a method that was followed prior to the publication of the OpenWrt ampr-ripd package.		STOP HERE. What follows is an explanation of how to manually install and configure ampr-ripd. This was a method that was followed prior to the publication of the OpenWrt ampr-ripd package. It is retained for reference and historical purposes.

	== Manual setup and configuration of OpenWrt ==		== Manual setup and configuration of OpenWrt ==