Setting up a gateway on MikroTik Routers - Revision history

KI5QKX: mw push

2026-03-01T00:14:52Z

mw push

← Older revision		Revision as of 00:14, 1 March 2026
Line 74:		Line 74:

	[[Category:How-To Guides]]		[[Category:How-To Guides]]
			[[Category:Infrastructure]]
			[[Category:Gateways]]

KI5QKX at 20:19, 12 December 2024

2024-12-12T20:19:24Z

← Older revision		Revision as of 20:19, 12 December 2024
Line 71:		Line 71:

	The Commands to run it can be found here http://www.yo2loj.ro/hamprojects/ampr-gw-README.txt		The Commands to run it can be found here http://www.yo2loj.ro/hamprojects/ampr-gw-README.txt


			[[Category:How-To Guides]]

4Z4ZQ at 17:23, 30 May 2017

2017-05-30T17:23:24Z

← Older revision		Revision as of 17:23, 30 May 2017
Line 29:		Line 29:

	/interface ipip		/interface ipip
	add allow-fast-path=no ~~!keepalive~~ local-address=10.0.0.180 name=UCSD \		add allow-fast-path=no local-address=10.0.0.180 name=UCSD \
	remote-address=169.228.34.84		remote-address=169.228.34.84

			Make sure to check that no keep alive is active on that interface as the amprnet router dont like the keep alive data .

	Now some routes commands needed to be done		Now some routes commands needed to be done

Kb3vwg: new AMPRGW IP

2017-05-26T20:22:37Z

new AMPRGW IP

← Older revision		Revision as of 20:22, 26 May 2017
Line 22:		Line 22:
	Fill in the local address field your router address on the DMZ (in home it will probably be 10.0.0.x or 192.168.1.x)		Fill in the local address field your router address on the DMZ (in home it will probably be 10.0.0.x or 192.168.1.x)

	At the remote address fill the address of the AMPRNET router (169.228.66.~~251~~)		At the remote address fill the address of the AMPRNET router (169.228.34.84)

	Press the apply button and you are done		Press the apply button and you are done
Line 30:		Line 30:
	/interface ipip		/interface ipip
	add allow-fast-path=no !keepalive local-address=10.0.0.180 name=UCSD \		add allow-fast-path=no !keepalive local-address=10.0.0.180 name=UCSD \
	remote-address=169.228.66.~~251~~		remote-address=169.228.34.84

	Now some routes commands needed to be done		Now some routes commands needed to be done
Line 48:		Line 48:
	You do it by the web as follows : IP ---> routes ---> add new		You do it by the web as follows : IP ---> routes ---> add new

	at the screen , type in the destination address 169.228.66.~~251~~/32		at the screen , type in the destination address 169.228.34.84/32
	and at the gateway , type the ip address of the next router (for home network , it is usually 10.0.0.138 or 192.168.1.1)		and at the gateway , type the ip address of the next router (for home network , it is usually 10.0.0.138 or 192.168.1.1)

Line 54:		Line 54:

	/ip route		/ip route
	add distance=1 dst-address=169.228.66.~~251~~/32 gateway=10.0.0.138		add distance=1 dst-address=169.228.34.84/32 gateway=10.0.0.138

	Now you should have connectivity from your 44 Net to the rest of the world (but not to any other 44 net networks worldwide )		Now you should have connectivity from your 44 Net to the rest of the world (but not to any other 44 net networks worldwide )

4Z4ZQ at 17:38, 15 May 2017

2017-05-15T17:38:21Z

← Older revision		Revision as of 17:38, 15 May 2017
Line 3:		Line 3:
	The example here will show the router that the WAN Port is connected to the DMZ of your Main router (the one that you get the ISP from it) and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)		The example here will show the router that the WAN Port is connected to the DMZ of your Main router (the one that you get the ISP from it) and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)

	Before you start configure the DMZ of your main router at least to allow two ~~way trafic~~ to the ~~UCSD Router~~ and make sure that the wan of the mikrotik router have ip on the same network of your DMZ and check that the MikroTik Interface can communicate with the Main ISP router		Before you start configure the DMZ of your main router at least to allow two direction (Incoming/Outgoing) traffic to the InterNet and make sure that the wan of the mikrotik router have ip on the same network of your DMZ and check that the MikroTik Interface can communicate with the Main ISP router

	The configuration can be done with the web interface (webFig) or in manual text command with telnet or SSH connection to the router		The configuration can be done with the web interface (webFig) or in manual text command with telnet or SSH connection to the router

4Z4ZQ at 17:26, 15 May 2017

2017-05-15T17:26:46Z

← Older revision		Revision as of 17:26, 15 May 2017
Line 2:		Line 2:

	The example here will show the router that the WAN Port is connected to the DMZ of your Main router (the one that you get the ISP from it) and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)		The example here will show the router that the WAN Port is connected to the DMZ of your Main router (the one that you get the ISP from it) and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)

			Before you start configure the DMZ of your main router at least to allow two way trafic to the UCSD Router and make sure that the wan of the mikrotik router have ip on the same network of your DMZ and check that the MikroTik Interface can communicate with the Main ISP router

	The configuration can be done with the web interface (webFig) or in manual text command with telnet or SSH connection to the router		The configuration can be done with the web interface (webFig) or in manual text command with telnet or SSH connection to the router

4Z4ZQ at 17:20, 15 May 2017

2017-05-15T17:20:01Z

← Older revision		Revision as of 17:20, 15 May 2017
Line 1:		Line 1:
	To setup a Gateway you need to have mikrotik router (all models support IPIP by default)		To setup a Gateway you need to have mikrotik router (all models support IPIP by default)

	The example here will show the router that the WAN Port is connected to the DMZ of your ~~Network~~ and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)		The example here will show the router that the WAN Port is connected to the DMZ of your Main router (the one that you get the ISP from it) and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)

	The configuration can be done with the web interface (webFig) or in manual text command with telnet or SSH connection to the router		The configuration can be done with the web interface (webFig) or in manual text command with telnet or SSH connection to the router

4Z4ZQ at 17:18, 15 May 2017

2017-05-15T17:18:45Z

← Older revision		Revision as of 17:18, 15 May 2017
Line 1:		Line 1:
	To setup a Gateway you need to have mikrotik router (all models support IPIP by default)		To setup a Gateway you need to have mikrotik router (all models support IPIP by default)

	The example here will show the router that the WAN Port is connected to the DMZ of your Network and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)		The example here will show the router that the WAN Port is connected to the DMZ of your Network and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)

4Z4ZQ at 17:18, 15 May 2017

2017-05-15T17:18:21Z

← Older revision		Revision as of 17:18, 15 May 2017
Line 1:		Line 1:
	~~The MikroTik Routers~~ ~~by default~~ support ~~IP-IP tunneling so setting up a gateway is quiet easy~~		To setup a Gateway you need to have mikrotik router (all models support IPIP by default)

	The example here will show the router that the WAN Port is connected to the DMZ of your Network and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)		The example here will show the router that the WAN Port is connected to the DMZ of your Network and the 44 Net will appear on the Lan Port (wan and lan Referring to a home router model)

Line 13:		Line 12:
	Now a tunnel interface have to be created between your router and the main AMPRNet router		Now a tunnel interface have to be created between your router and the main AMPRNet router

	You do it in the web by this : interfaces ---> Add New --> IP tunnel		You do it in the web by this : interfaces ---> Add New --> IP tunnel ,
	a Screen will open		a Screen will open

4Z4ZQ at 17:56, 22 April 2017

2017-04-22T17:56:08Z

← Older revision		Revision as of 17:56, 22 April 2017
Line 11:		Line 11:
	Now chose which interface you assign this IP for , there is a drop down menu that show all of your interfaces , chose the one that connected to the local net		Now chose which interface you assign this IP for , there is a drop down menu that show all of your interfaces , chose the one that connected to the local net

	Now a tunnel interface ~~must~~ be created between your router and the main AMPRNet router		Now a tunnel interface have to be created between your router and the main AMPRNet router

	You do it in the web by this : interfaces ---> Add New --> IP tunnel		You do it in the web by this : interfaces ---> Add New --> IP tunnel
Line 18:		Line 18:
	Change the name to say UCSD		Change the name to say UCSD

	~~Add~~ in the local address your router address on the DMZ (in home it will probably be 10.0.0.x or 192.168.1.x)		Fill in the local address field your router address on the DMZ (in home it will probably be 10.0.0.x or 192.168.1.x)

	At the remote address ~~put~~ the address of the AMPRNET router (169.228.66.251)		At the remote address fill the address of the AMPRNET router (169.228.66.251)

	Press the apply button and you are done		Press the apply button and you are done