Setting up a gateway on OpenWRT: Difference between revisions
Jump to navigation
Jump to search
Created page with "ampr-ripd has been compiled for Atheros 71xx == Summary == Install: * kmod-ipip * ip-full * ampr-ripd to '''/etc/config/''' * a bridge interface to tunl0 and a new VLAN..." |
|||
| Line 7: | Line 7: | ||
* kmod-ipip | * kmod-ipip | ||
* ip-full | * ip-full | ||
* ampr-ripd to '''/etc/config/''' | * [[ampr-ripd]] to '''/etc/config/''' (always run [[RIP]]44 software in console mode FIRST after installation to verify execution and obtain the password, the execution of the file is commented-out below) | ||
* a bridge interface to tunl0 and a new VLAN, adding it to it's own firewall zone | * a bridge interface to tunl0 and a new VLAN, adding it to it's own firewall zone | ||
* a VLAN to any switch/trunk ports (as desired) | * a VLAN to any switch/trunk ports (as desired) | ||
| Line 16: | Line 16: | ||
ifconfig tunl0 mtu 1480 up | ifconfig tunl0 mtu 1480 up | ||
iptables -t filter -I INPUT -p 4 -i eth0.2 -j ACCEPT | iptables -t filter -I INPUT -p 4 -i eth0.2 -j ACCEPT | ||
./etc/config/ampr-ripd -p '''<PASSWORD>''' -t 44 -a 44.60.44.0/24 | '''# ./etc/config/ampr-ripd -p '''<PASSWORD>''' -t 44 -a 44.60.44.0/24''' | ||
ip route add default dev tunl0 via '''<AMPRGW>''' onlink table 44 | ip route add default dev tunl0 via '''<AMPRGW>''' onlink table 44 | ||
ip route add '''<44.xxx.xxx.xxx/xx>''' src '''<44.xxx.xxx.xxx>''' dev '''<br-amprnet>''' table 44 | ip route add '''<44.xxx.xxx.xxx/xx>''' src '''<44.xxx.xxx.xxx>''' dev '''<br-amprnet>''' table 44 | ||
Revision as of 03:05, 15 August 2015
ampr-ripd has been compiled for Atheros 71xx
Summary
Install:
- kmod-ipip
- ip-full
- ampr-ripd to /etc/config/ (always run RIP44 software in console mode FIRST after installation to verify execution and obtain the password, the execution of the file is commented-out below)
- a bridge interface to tunl0 and a new VLAN, adding it to it's own firewall zone
- a VLAN to any switch/trunk ports (as desired)
(eth0.2 in this case is the Public-facing WAN (to allow IPENCAP traffic), read your OpenWRT hardware Wiki for your specific model
ifconfig tunl0 mtu 1480 up iptables -t filter -I INPUT -p 4 -i eth0.2 -j ACCEPT # ./etc/config/ampr-ripd -p <PASSWORD> -t 44 -a 44.60.44.0/24 ip route add default dev tunl0 via <AMPRGW> onlink table 44 ip route add <44.xxx.xxx.xxx/xx> src <44.xxx.xxx.xxx> dev <br-amprnet> table 44 ###OPTIONAL FOR LAN### ip route add 192.168.0.0/16 src 192.168.x.x dev br-lan table 44 ### ip rule add to 44.0.0.0/8 table 44 priority 44 ip rule add from 44.0.0.0/8 table 44 priority 45
- create any forwarding rules