Firewalls

Welcome to the Firewall Wiki.

NOTE: This page is intended to be edited by the community to add use practices, command syntax, etc. regarding firewalling and security on AMPRNet nodes. While each operator is ultimately responsible for the administration of their node, it is highly suggested amongst the 44Net mailing list Community that nodes be firewalled.

NOTE: On an iptables-based firewall, you must enable connection tracking on the tunl0 interface in order to enable Stateful Packet Inspection (i.e. a stateful firewall). Since the IPENCAP Linux Kernel Module IPIP is in the kernel, you must set the default forwarding policy to DROP or REJECT. If you set your default routing policy to ACCEPT, all packets that have not been explicitly DROPped or REJECTed elsewhere, will route, regardless of firewall policies.

D-Link

On some D-Link devices, the port forwarding feature allows for the options: TCP, UDP and Other. The "Other" option on these models are capable of Destination NAT of IPENCAP packets.

To enable input of IPENCAP (IP Protocol Number 4) Note: this rule is required for other AMPR nodes to initiate inbound traffic to your node.

In Port Forwarding

# Create a new Port Forward
# Enter the LAN IP of your AMPR node
# Select "Other"
# Type the number 4 into the field

iptables

To enable input of IPENCAP (IP Protocol Number 4) Note: this rule is required for other AMPR nodes to initiate inbound traffic to your node.

iptables -t filter -I INPUT -p 4 -i <INTERFACE OF YOUR WAN> -j ACCEPT 

If your AMPR node is downstream, you will create an INPUT and DNAT forward rule to the destination LAN IP of your AMPR node.

To enable receipt of RIP44

iptables -t filter -I INPUT -p udp -s 44.0.0.1 --sport 520 -d 224.0.0.9 --dport 520 -i tunl0 -j ACCEPT 

############################################################
# DROPS IP TRAFFIC THAT'S INVALID ENTERING OR EXITING AMPR
# THIS PREVENTS A GENERAL LOOP
iptables -I FORWARD -i tunl0 -o tunl0 -j DROP
# DROPS OUTBOUND IPs NOT FROM YOUR ALLOCATION (BCP 38)
iptables -t raw -I PREROUTING ! -s 44.xxx.xxx.xxx/xx -i br-amprnet -j DROP
# DROPS ROGUE INBOUND ASSIGNED IPs FROM LOOPING THROUGH tunl0 VIA IPENCAP
iptables -t raw -I PREROUTING -s 44.xxx.xxx.xxx/xx -i tunl0 -j DROP
# DROPS OUTBOUND UNASSIGNED IPs FROM LOOPING THROUGH tunl0 VIA IPENCAP
# YOU MUST ADD A RULE UNDER THIS LINE TO MAKE EXCEPTIONS (BCP 38)
iptables -I FORWARD ! -s 44.xxx.xxx.xxx/xx -o tunl0 -j DROP
############################################################
# DROPS BOGONS ENTERING AMPRNet
# SEE http://www.team-cymru.org/Services/Bogons/bogon-bn-nonagg.txt
iptables -t raw -I PREROUTING -s 0.0.0.0/8 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 10.0.0.0/8 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 100.64.0.0/10 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 127.0.0.0/8 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 169.254.0.0/16 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 172.16.0.0/12 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 192.0.0.0/24 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 192.0.2.0/24 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 192.168.0.0/16 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 198.18.0.0/15 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 198.51.100.0/24 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 203.0.113.0/24 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 224.0.0.0/4 -i tunl0 -j DROP
iptables -t raw -I PREROUTING -s 240.0.0.0/4 -i tunl0 -j DROP
############################################################
# THIS PREVENTS NESTED IPENCAP (BCP 38)
iptables -t raw -I PREROUTING -p 4 -i tunl0 -j DROP

OpenWRT

See: iptables (above) and the Instructions for setting up a gateway on OpenWRT.

iptables-based rules can be entered in Network > Firewall > Custom Firewall on the LuCI web interface; or via the command prompt via UCI.