Difference between revisions of "Setting up a gateway on OpenWRT"

From ARDC
Jump to navigation Jump to search
Line 33: Line 33:
 
   
 
   
 
* '''reboot'''
 
* '''reboot'''
* a bridge interface to tunl0 and a new VLAN, adding it to its own firewall zone (assign an IP from your allocation to this interface)
+
* a bridge interface to tunl0 and a new VLAN, adding it to its own firewall zone (assign an IP from your allocation to this interface), using Input: Drop or Reject, Output: Accept and Forward: Drop or Reject
 
* the VLAN to any switch/trunk ports (as desired)
 
* the VLAN to any switch/trunk ports (as desired)
 
* create any forwarding/input firewall Traffic Rules
 
* create any forwarding/input firewall Traffic Rules

Revision as of 17:06, 15 August 2015

ampr-ripd has been compiled for Atheros 71xx

NOTE: To operate a Gateway on AMPRNet, you must have a method of obtaining up-to-date route information. On AMPRNet, a variant of RIP version 2 protocol, named RIP44 is used. RIP version 2 is not the same as RIP44. rip44d is written in the Perl programming language by Heikki Hannikainen, OH7LZB. ampr-ripd is written in C by YO2LOJ. The routing table is relatively small, so the performance or memory consumption of this daemon isn't very critical. ampr-ripd is used in this instance, so no other prerequisite software is required to run the RIP44 daemon.

  • You must have access to a binary executable of ampr-ripd that is compatible with the CPU in your OpenWRT device (e.g. i386, i586, x86_64, MIPS, PPC, etc.). If you do not, you must compile ampr-ripd yourself, or install the packages necessary to run rip44d.

See

Summary

Install:

  • kmod-ipip
  • ip-full
  • ampr-ripd to /etc/config/ (always run RIP44 software in console mode FIRST after installation to verify execution and obtain the password, the execution of the file is commented-out below)
  • the following to Firewall > Custom Rules:
# (eth0.2 in this case is the Public-facing WAN (to allow IPENCAP traffic), read your OpenWRT hardware Wiki for your specific model 
ifconfig tunl0 mtu 1480 up
iptables -t filter -I INPUT -p 4 -i eth0.2 -j ACCEPT
# ./etc/config/ampr-ripd -p <PASSWORD> -t 44 -a <44.xxx.xxx.xxx/xx>
ip route add default dev tunl0 via <AMPRGW> onlink table 44
ip rule add to <44.xxx.xxx.xxx/xx> table main priority 44
#OPTIONAL LAN ### ip rule add from <44.xxx.xxx.xxx/xx> to <192.168.xxx.xxx/16> table main priority 45
ip rule add from 44.0.0.0/8 table 44 priority 46
### CREATE A BLACKHOLE ON TABLE 7777 ###
ip route add default dev lo src 127.0.0.1 table 7777
### BLACKHOLE ALL REMAINING AMPR TRAFFIC ON TUNNEL ###
ip rule add to 44.0.0.0/8 dev tunl0 table 7777 priority 7777

  • reboot
  • a bridge interface to tunl0 and a new VLAN, adding it to its own firewall zone (assign an IP from your allocation to this interface), using Input: Drop or Reject, Output: Accept and Forward: Drop or Reject
  • the VLAN to any switch/trunk ports (as desired)
  • create any forwarding/input firewall Traffic Rules
  • test ampr-ripd in console using the -d argument
  • add password to Custom Rule and uncomment ampr-ripd line
  • reboot